The propeller, Mavic Mini Propeller Spinning Too Fast is one of the most important pieces of a drone. It’s typical for drone propellers to malfunction due to excessive rotation speed, which can significantly impact how well your drone performs.
In this article, we will discuss possible reasons for this phenomenon and explain that you don’t have to worry because our team of trained professionals can fix the problem.
When propellers are damaged, they spin too quickly which makes the drone impossible to balance in the air and control. So when a drone loses one of its forward-facing propellers then it can unexpectedly tilt in that direction.
In the past, there was no way to tell if new components had caused propellant overspending, but DJI Phantom 4 now displays a Mavic Mini motor speed error warning to alert the user to the pricey problem.
Some DJI Mavic Mini users claim that the “Motor Speed Error” message is an error on the user’s part, but have discovered through experience that it isn’t so.
Downgrading their firmware removes their mistake message, but does not resolve the underlying issue. When a customer’s drone falls from the sky, they should be prepared (it happens – so there are no guarantees.
Read also: What Happens If Mavic Mini Loses Connection?
What Causes The “Motor Speed Error” Warning To Appear?
Damage to your propeller is one of the most common reasons for a Propeller Error. Bent or broken propellers can cause your multi-rotor to lose lift and end up crashing.
Bent propellers are damaged in almost all circumstances that cause an accident, and it’s important to remember to replace them at once if you suspect that they are damaged.
How Can I Resolve A Motor Speed Error Message?
When your DJI drone displays the “Mavic Mini Propeller upgrade” notification, immediately land the aircraft and then double-check that the blades are in good condition at a nearby landing area.
If you notice damage to any of them, remove them carefully according to this guide and replace them with new ones.
Maintaining your drone properly will help it last a lot longer! That’s because using damaged propellers, like any other type of broken or damaged equipment, can cause the entire system to overload and eventually break down.
How Can Propellers Be Kept In Good Condition?
One of the most common mistakes made by people who are new to drones is to fly them in areas that have many obstacles like trees, buildings, and other parts of the environment.
To avoid causing damage to your drone or propellers (especially if it’s a smaller quadcopter), make sure you equip your drone with propeller guards prior to starting it up and flying around in an area where there are obstacles. It also helps if you fly more carefully and keep this in mind for future flights as well.
Drone propellers should be stored in a safe place when they are not being used. Read this guide on how to safely store your drone propellers.
To keep your drone propellers in good shape, fold them up horizontally or remove them completely before shipping out your drone so they will not be bent or forced down during transportation.
Keeping your drone in storage for an extended period can be risky. Propellers could be forced down which means opening them up and cleaning them out.
Back propellers are more likely to be damaged than the front ones. This can be prevented by using the Fly More Combo Soft Case. Lower propellers can be rotated to face the gimbal or parallel with it.
Propellants in this position are not under any stress in this case, and it is also easier for them to stay in a stable state before the flight.
When it comes to handling your drone and batteries, protection of the latter is extremely important. Additionally, handling the drone with care will also prolong its life.
In order to prevent propellers from being warped by heat from the plane or batteries, it’s recommended that you store them separately after every use.
How Do You Replace The Propellers On A Drone?
Each propeller on an aircraft must be supported by a low-pressure airfoil made of plastic, carbon fibre, aluminum or similar materials. These plastic blades help move the drone quickly through the air in order to help the aircraft navigate more easily.
If any of these propellers are broken or cracked, you should consider replacing them right away to avoid putting yourself, your drone and others nearby at risk. The process of changing a propeller on your drone is quite simple if you’re handy with tools and have experience handling your particular model.
However, if you need help performing this task, take it to a professional immediately as improper propeller replacement could lead to unexpected fallout such as ruined flight controllers which will impair how well your drone is able to function later down the road.
To change the propellers, you will need a screwdriver and the same screws that came with your drone. Propellers come in categories: clockwise and counterclockwise.
Make sure both of them replace the same shears on the motor. Use the manual to verify that you’re using the correct diameter sizes for your robot.
To change your propellers, below are a few basic procedures to follow:
Step 1: Unscrew the propeller’s screws using a screwdriver. Place the driver on the cross recess and crank it counter-clockwise to unscrew it.
Step 2: With both of your propellers malfunctioning and you on a tight schedule, adding your own replacement parts can sometimes save you the time and the money of fixing or buying a brand new motor. Simply remove anything that’s still attached to the defective motor and throw it in the trash for easier cleaning later.
Before you attach the propeller to your drone, you’ll need to remove the thread locker from the hole. Use a pipe cleaner to clean out debris, re-attach the propeller a few times or use grease if there are any lingering issues.
Step 3: It’s time to insert the new screws into the driving shaft with the screwdriver in step 3. As soon as you’ve finished aligning the screws, tighten them down by turning the screws clockwise with a screwdriver.
Step 4: In order to drive the screws in as far as you can without encountering too much resistance, make sure you’re using a screwdriver that is of the right size. If the screws are placed correctly (and are not rusted or dirty), there shouldn’t be any problem driving each of them in during assembly…just don’t apply a lot of pressure.
Step 5:The screws should be tightened now. Drive in the screws until they are well seated in their sockets before doing this
Step 6: After you’ve finished installing the screws, give your propeller a good hard pull to see if it moves freely. If all went well, it should move without any problems.
Step 7: If you’d like to be ready in the future, you should order some new propellers now. For example, order a spare ESC beeping Mavic Mini at the same time that you order new props so as to prevent downtime if you need to swap out your props in a hurry.
Read Also: Can You Fly Mavic Mini Without Internet?
This post has all of the information about how to spin the propellers on your Mavic Mini propeller problems in a way that won’t make you dizzy. We hope it helps resolve this issue.
Frequently Asked Questions
How can I stop my Mavic Mini’s ESC from beeping?
Make a note of the beeping ESCs should you receive this message. Props can experience problems such as warping, flattening, or cracking, and they should be checked thoroughly to ensure they haven’t been damaged in any way.
You should refer to the recommendations in the message if there are no other issues present (profiling or wind-related). If that doesn’t work you may need to exchange the ESCs themselves.
Is there gimbal control on the Mavic Mini?
Drones like DJI’s Mavic Mini can capture photos and videos that are crisp, clear and consistently awesome thanks to a camera that can shoot 2.7K video and 12MP images along with impressive flight stability due to the three-axis gimbal and 1/2.3″ sensor looking down at the world below it.
The drone’s sophisticated flight control system makes sure this little machine is safe and easy to use when needed while the integrated backup systems give you complete confidence in your smart flying companion just in case things go wrong.
How often should I replace the propeller on my Mini 2?
Thank you for your question. For safety reasons, we do not recommend rotating airplane propellers. Using a screwdriver can damage the screws and/or the threads of the rear landing wheel.
When should I get a new propeller for my drone?
Propellers should be replaced whenever they show signs of wear, such as cracks, nicks, or distortion. If any of your props are missing pieces or tips, do not fly your drone. Having a quieter drone is especially beneficial if you plan to fly over densely populated regions.
It’s incredibly important to replace worn-out or broken propellers on your drone as with each flight there’s a chance that you could snap them and hurt people passing below during an accident.
The better your propeller, the more energy it can store and use to accelerate. Moreover, vibration resistance will decrease which causes the motor to shake at high speeds touching the frame and eventually destroying the engine in some cases.
Hello, My name is Shari & I am a writer for the ‘Outlook AppIns’ blog. I’m a CSIT graduate & I’ve been working in the IT industry for 3 years.